Structural / Civil Inspector (Contract)
SGS • Calgary, AB, CA
5 hours ago
Salary
CA$75.00–CA$90.00 hourly
Job type
- Contractor
Job description
Job Description
SGS is looking for Structural/Civil Inspectors (Contract) for site locations and shops. The assignement would start in January 2027 and would be on going.
- Locations: Site inspections in Kitimat, BC; shop/vendor inspections across BC and Alberta.
- Pay: $75–$90/hour for site work; $55–$60/hour for shop work.
- Start: January 2027.
- Schedule: Intermittent/as needed—not guaranteed full-time hours.
Structural (Shop):
- verification of structural steel materials, fabrication, welding, surface treatment, erection, and installation to ensure compliance with approved engineering drawings, project specifications, applicable codes, and quality requirements
- Review approved fabrication drawings, specifications, ITP, QCP, WPS/PQR/WPQ and fabrication procedures
- Attend kick-off, pre-inspection meetings, witness, surveillance and hold points, as required
- Verify material grades, MTRs, dimensions, identification, heat numbers and traceability
- Inspect cutting, beveling, edge preparation, fit-up and dimensional accuracy
- Review welding procedures and qualifications; inspect fit-up, preheating, welding parameters and workmanship
- Verify RT, UT, MT and PT activities, procedures, personnel qualifications and reports as specified
- Check member lengths, profiles, straightness, squareness, hole locations, connection details and tolerances
- Verify bolt grades, sizes, hole dimensions, nuts, washers and connection arrangements
- Inspect abrasive blasting, surface cleanliness, surface profile and environmental conditions
- Verify coating specifications, application, DFT, curing and holiday testing where applicable
- Verify overall workmanship, identification, marking, preservation, packaging and shipment readiness
- Prepare detailed reports documenting inspection results, including any issues found.
- Recording inspection results and any non-conformities
- Investigating Non-Conformities identifying causes and assisting in corrective actions.
Structural (Site):
- Covering steel erection, alignment, bolted connections, field welding, anchor bolts, grouting and structural installation.
- Verify delivered structural steel components, identification, traceability and transportation damage.
- Inspect anchor bolts, base plates, embedded plates, grout and supporting foundations
- Verify installation of columns, beams, bracing, trusses, platforms and structural connections
- Check structural alignment, plumbness, elevations, dimensions and tolerances
- Verify bolt grades, installation, tightening, pre-tensioning and inspection records.
- Verify WPS/WPQ, joint preparation, fit-up, welding workmanship and applicable preheat requirements.
- Witness or review field weld NDE activities and reports as required by the ITP
- Verify changes, repairs and deviations against approved engineering drawings and dispositions
- Inspect coating damage, surface preparation, touch-up painting, DFT and fireproofing where applicable
- Verify structural completeness, connection integrity, outstanding deficiencies and final acceptance documentation.
CIVIL (Site):
- monitoring and verifying civil construction activities to ensure compliance with approved engineering drawings, project specifications, applicable codes, construction procedures, and quality requirements.
- Site Preparation and Earthworks
- Foundation and Reinforcement Inspection
- Concrete Inspection and Testing
- Inspection of Underground Utilities and Drainage
- Inspection of Waterproofing and Protective Systems
- Experience in soil classification, compaction and field density testing
- Experience in rebar inspection, formwork and foundation construction
- Experience in underground piping, drainage, trenching and utility installation
- Experience with ITPs, QCPs, NCRs, quality documentation and construction surveillance
Qualifications
Structural
- CWB-Level 2 with structural steel welding experience
- Familiarity with CSA , W59, S16, ASTM, ASME IX, SSPC, etc..
- Civil/Structural/Mechanical Engineering degree or diploma
- 5+ years of fabrication and inspection experience at manufacturing shops
- 5+ years of fabrication and inspection experience at site
- Experience in fabrication and erection surveillance, ITP implementation, NCR management and quality documentation
Civil:
- ACI Grade I / ICC Reinforced Concrete SI
- Bachelor's degree or diploma in Civil Engineering or Construction Engineering Technology
- Minimum 5 years of relevant civil construction inspection experience
- ACI Concrete Field Testing Technician or equivalent certification
- Familiarity with CSA / , ACI 318 / 301, etc.
Additional details:
Work schedule and hours of work: Intermittent when & where required subject to job requirement
Pay Rate (site): $75/hr. to $90/hr.
(Shop): $55/hr. to $60/hr.
Per diems (Shop): Expenses will be covered at cost if inspection site is beyond round trip 200 kms from Inspector place of residence and requires overnight stay at hotel
Per diems (Site): Expenses will be covered at cost